Step Plumbing Guide for Bathtub Installation
Step Plumbing Guide for Bathtub Installation
Blog Article
We've stumbled on this article relating to Installing A Bathtub below on the net and figured it made perfect sense to share it with you on this site.
Setting up a bath tub isn't exactly rocket science, however it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging project. If the old tub is readily easily accessible, the job can move easily; if you have to open up a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to leave the old tub and set in the brand-new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. As opposed to working with a service provider to take over a halfway-completed task, it is much better to consider employing one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This post will certainly aid you set up a new tub in your restroom if you have currently acquired a brand-new bathtub and also don't require to change the plan of your previous water supply pipelines.
Your tools and also material list ought to comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to going on to fit the new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet as well as the sink. Secure the tap in place with the supplier given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind ought to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Switch on the water supply and also examine all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub as well as additionally examine the overflow outlet and also the typical electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been made use of at least once as this will certainly resolve it right into its final placement.
Getting ready for the Setup
Firstly, the sustaining structure provided with the bath ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its final setting.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, resulting in difficulties with wetness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very focused on Installing A Bathtub and I'm hoping you appreciated the new blog post. Sharing is nice. One never knows, you may very well be doing someone a favor. Thanks so much for your time spent reading it.
Need quality service? Report this page